Gateway reuse

To reuse your gateway:

  1. You have to delete the manually all devices links to the account from the app
  2. Then delete the customer account that is linked to the gateway from the customer service tool.
  3. Then you have to perform a factory reset of the gateway. For the NA502/NA502S: Insert a pin in the ⟲-hole for 30 seconds, all lights should turn off.
  4. Next step is to click the admin button in CS tool in the customer service tool and go to "Gateway Blacklist". Find the MAC address of the gateway you just factory reset and remove it from the blacklist.
  5. The gateway should now be ready to be reused.

Fibaro Motion Sensor 

The device can be factory reset using the following process:

  1. Open sensor
  2. Press and hold button (10-15 seconds)
  3. The light will start to change colour. Release button when light turns yellow
  4. Quickly press button once to confirm reset
  5. After a couple of seconds it will blink red to confirm reset

Fibaro Wall Plug

The device can be factory reset using the following process:

  1. Press and hold button (10-15 seconds)
  2. The light will start to change colour. Release button when light turns yellow
  3. Quickly press button once to confirm reset
  4. After a couple of seconds it will blink red to confirm reset

Aeotec Smart Switch

The device can be factory reset using the following process:

  1. Press and hold button for 20 seconds
  2. The LED light will glow solid for 2 seconds then begin to blink to confirm reset

Viva HD IP Indoor Camera


The device can be factory reset using the following process:

  1. Boot up the camera (plug power)
  2. Wait around 1 min for the boot to be fully finished, no led should be ON
  3. Press and hold reset button for around 15 seconds until you hear a short music sound to confirm reset (if not, please try again from step 1)
  4. Release the reset button and wait for the camera to reboot completely (like in step 2)

Aeotec Door/Window Sensor


The device can be factory reset using the following process:

  1. Open door sensor
  2. Press and hold Z-Wave button for 20 seconds
  3. Release button. The light will blink for 3 seconds to confirm factory reset

Aeotec Siren


The device can be factory reset using the following process:

  1. Press and hold button for 20 seconds
  2. The siren will sound for 3 seconds to confirm factory reset 

Aoetec Panic button


The device can be factory reset using the following process:

  1. Insert the included button pin (or a paper clip bent to fit both holes), into both both the "learn" and "Include/exclude" holes, then press and hold for 10 seconds.
  2. If successful, the green and red LED on the front of your Panic Button will blink in an alternate pattern followed by the green LED illuminating for 2 seconds. If unsuccessful, the red LED will illuminate for 2 seconds. If this occurs, repeat the process again.
     

Smoke detector (FGSD-002 ZW5)


The device can be factory reset using the following process:

  1. Press and hold button until it makes a short noise and starts blinking slowly (5 seconds).
  2. The light will start to change colour. When light turns yellow, press once the button to confirm reset.
  3. After a couple of seconds it will blink red and make one short noise to confirm reset.

Flood sensor

The device can be factory reset using the following process:

Trigger flood sensor 10 times within 10 seconds by dipping it a glass of water
 

Viva HD IP outdoors camera


The device can be factory reset using the following process:

  1. Connect the camera to a power source.
  2. Wait around 1 min for the camera to boot up.
  3. Press and hold reset button for around 15 seconds.
  4. Release the reset button and wait for the camera to reboot completely. (like in step 2)

Alarm Control Button


The device can be factory reset using the following process:

  1. Press all 4 buttons together for 10 seconds.
  2. The LED colors will turn red after 2 seconds for 2 seconds and turn green for another 2 seconds.
  3. The device is now factory reset.

Outdoor Siren


The device can be factory reset using the following process:

  1. Open the device by unscrewing the bottom screw.
  2. Locate the "Function" button.
  3. Press and hold the "Function" button for 10 seconds.
  4. All three LEDs will flash at once to confirm the factory reset.

Danalock V3


The device can be factory reset using the following process:

  1. Push the pin-hole button 10 times.
  2. The LED indicator should now be red, push the pin-hole once to confirm the factory reset.

Zigbee Lights


Ikea Tradfri: https://www.youtube.com/watch?v=mJm9YpPrGzk

Philips HueFactory resetting Philips Hue bulbs

 

Z-Wave extender (ZW117-C)


The device can be factory reset using the following process:

  1. Press and hold button for 20 seconds
  2. The green LED will be solid for 2 seconds and then remain the colourful gradient status to confirm factory reset

Danfoss Radiator Thermostat Valve LC-13


The device can be factory reset using the following process:

  1. Remove the battery cover and take out one battery
  2. Press and hold the bottom centre button for 5 seconds, while reinserting the battery
  3. The device is now factory reset

 

NodOn Wall Switch CWS-3-1-0x


The device can be factory reset using the following process:

  1. Press and hold the bottom 2 buttons for 1 second
  2. Release buttons. The devices is now factory reset